How do I access Cisco SG300?

Start your web browser, and enter the IP address of the switch. By default, the address of the switch is set to 192.168. 1.254, and the username and password are both “cisco”.

How do I configure a Cisco Managed switch?

How to configure Cisco switch?

  1. Initial command prompt “Switch>” appears on the screen.
  2. Type “enable” next to it and press “Enter”.
  3. This will take you into the “EXEC” mode, also known as the Global Configuration mode.
  4. Go into configure mode using configure terminal.
  5. Enter the configuration commands one per line.

How do I access Cisco Small Business switch?

To access the switch by using the web-based interface, you must know the IP address the switch is using. The switch uses the factory default IP address of 192.168. 1.254 by default. When the switch is using the factory default IP address, the System LED flashes continuously.

Is Cisco SG300 a PoE switch?

The SG300-28PP 24-Port 10/100/1000 Gigabit PoE Managed Switch from Cisco is designed to support a variety of PoE devices from access points to VoIP phones, and much more. On the switch you will find a total of 26 Gigabit ports, 24 of which are PoE+ compatible, with the other two providing combo mini-GBIC connectivity.

How do I find the IP address of a Cisco SG300 switch?

Open your Internet browser and digit the default IP address of the switch: http://192.168.1.254. The Default User ID and Password for the unit is “Cisco”.

Is there a GUI for cisco switches?

A web browser, or graphical user interface (GUI), is built into each switch. You can use either the service port interface or the management interface to access the GUI. We recommend that you use the service-port interface.

Do cisco routers have a GUI?

Cisco Router Web SetUp Tool is a free software configuration utility, supporting the Cisco 800 series DSL routers, the 806 dual Ethernet router as well as the SOHO series. It includes a Web-based GUI that provides the following: Simplified Setup with AUTOMATIC DETECTION of proper setup. Advanced Configuration.

How do I configure a managed switch?

How to configure a network switch

  1. Step 1: Connect to the console.
  2. Step 2: Set a management IP and default gateway.
  3. Step 3: Set hostname and domain name.
  4. Step 4: Set logins on VTY lines and console port.
  5. Step 5: Set Privileged EXEC password.
  6. Step 6: Enable SSH.
  7. Step 7: Create VLANs.
  8. Step 8: Add access ports to a VLAN.

What are the steps to configure a switch?

  1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
  2. Step 2: Set up management IP.
  3. Step 3: Check VTP revision number.
  4. Step 4: Configure access ports.
  5. Step 5: Configure trunk ports.
  6. Step 6: Configure access ports.
  7. Step 7: Set up VTY line config.

What is managed switch?

What are managed switches? Managed switches let users adjust each port on the switch to any setting, enabling them to manage, configure and monitor the network in many ways. They also provide greater control over how data travels over the network and who can access that data.

How do I reset my sg300 switch?

First Method — Manual Reset

Press and hold the Reset button on the switch for atleast 20 seconds until all the port LEDs light up. The switch will reboot now. 3. Connect your PC directly to the switch using an Ethernet cable.

What is the default IP of cisco sg300?

192.168.1.254
Start your web browser, and enter the IP address of the switch. By default, the address of the switch is set to 192.168. 1.254, and the username and password are both “cisco”.

How do I find my cisco IP port?

Type at the console prompt sh arp to find the ip address and mac address then type sh mac-address-table to find the the mac and port.

How do I access switch GUI?

Choose Configuration > Switch > Management > Protocol Management > HTTP-HTTPS. The HTTP-HTTPS Configuration page appears. To enable web mode, which allows users to access the switch GUI using “http://ip-address,” choose Enabled from the HTTP Access drop-down list. Otherwise, choose Disabled.

How do I configure a switch?

How do I access my cisco router settings?

Open any web browser and type in 192.168. 1.1 in the address bar. This should be the default Cisco router IP address and will take you to your Cisco router login page.

How do I access my router interface?

Accessing Your Router’s Web Interface
This is as simple as plugging your router’s IP address into your web browser’s address bar and pressing Enter. If your have your router’s manual, you’ll find your router’s default IP address in the manual.

How do you tell if a switch is managed or unmanaged?

Unmanaged switches are designed to just plug in and run, with no settings to configure. These are fine to use in small networks with only basic needs. Managed switches, however, are fully configurable, are customizable, and provide a range of data on performance.

How do I configure a port on a switch?

Switch ports can be manually configured with specific duplex and speed settings. Use the duplex interface configuration mode command to manually specify the duplex mode for a switch port. Use the speed interface configuration mode command to manually specify the speed for a switch port.

How do I enter Cisco config mode?

To enter global configuration mode, enter the configure command. Global configuration From privileged EXEC mode, enter the configure command. To exit to privileged EXEC mode, enter the exit or end command, or press Ctrl-Z. To enter interface configuration mode, enter the interface configuration command.

How do you configure an IP address?

To enable DHCP or change other TCP/IP settings

  1. Select Start, then type settings. Select Settings > Network & internet.
  2. Do one of the following:
  3. Next to IP assignment, select Edit.
  4. Under Edit network IP settings or Edit IP settings, select Automatic (DHCP) or Manual.
  5. When you’re done, select Save.

What are the 4 types of switches?

The types of switches are classified into four types namely:

  • SPST (Single Pole Single throw)
  • SPDT (single pole double throw)
  • DPST (double pole, single throw)
  • DPDT (double pole double throw)

How do I know if my switch is managed or unmanaged?

How do I Reset my switch settings?

Step 1. Disconnect all Ethernet cables from the switch. Step 2. Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.

How do I Reset my cisco switch to factory settings?

Hold the “mode” button on the front of the switch for 10 seconds. The lights will blink then go solid – the switch completely wipes all configuration and then reboots.